Flextrak F4-V6.1 Now Available!
Flextrak is a PiZero form factor STM F4 based High Altitude Balloon Tracker.
This board has a GPS receiver and radio transmitter designed for tracking high altitude balloon flights utilising a Raspberry Pi Zero W. An optional APRS board is available see related items.
You will get :
- Flextrak F4-V6.2 Board
- Battery holder + clip
- 4 x 11mm Standoffs with screws to attach to the Pi+
- Standard non stacking low profile header
- RG174 Tail for making into a suitable antenna see this article.
- Pi Zero W Board with Camera Cable (Camera not supplied - please order separately)
- 32Gb SD Card preloaded with FlexTrak code.
- External DS18B20 Temperature Sensor
- GPS Stubby Antenna SMA-Male Straight
The board is supplied with a 434,868 or 915 MHz LoRa radio transmitter To track the location of flight you also need a suitable radio receiver, aerial and PC on the ground. It can be tracked with a mobile phone connected to our LoRaGo device.
It features:
- Efficient built-in power regulator providing run time of over 20 hours from 4 Energizer Lithium Ultimate AA cells (With no Pi - 11 hours with a Pi attached)
- Highly sensitive UBlox GPS receiver suitable for altitudes up to 50km
- Temperature sensor (Internal/External)
- Battery voltage monitoring
- Allows use of Raspberry Pi camera
- Mounting holes and spacers for a solid connection to the Pi
- Tracker will continue to work even if the Raspberry Pi fails.
- Flextrak can be used without attaching a Raspberry Pi at all.
- Solid SMA connector for GPS antenna - no more snapped off antennas!
The open-source software provides these features:
- Radio telemetry with GPS and sensor data using UKHAS standard
- Radio image download using SSDV standard
- Variable image size according to altitude
- Stores full-definition images as well as smaller transmitted images
- Automatically chooses better images for download
- Supplied as github repository with instruction
- Optional APRS transmission with additional hardware.
- On board landing prediction
Weight Breakdown:
Flextrak Board - 14g
Header + Standoffs - 14g
Battery Holder+Clip - 13g
PiZeroW + Cable - 14g
GPS Antenna - 19g
Not supplied for information only:
Energizer L91 Lithium (AA) - 14.5g x 4
Instruction Manual: Flextrak STM Manual
Flextrak settings can be programmed via Flextrak Config available here. To program the board connect a USB to serial connector to GND/ RX and TX only (Don't connect VCC). Can also be programmed directly from the attached Raspberry Pi.
Flextrak Raspberry Pi Kit
- Brand: Uputronics
- Product Code: HAB-FLEXTRAK
- Availability: 79
-
£240.00
- Ex Tax: £200.00
Available Options
Related Products
SMA to RG174 Pigtail
SMA male attached to a 30cms piece of RG174 coax cable. Suitable for making 1/4 wave antennas f..
£4.80 Ex Tax: £4.00
434/868/915MHz "Stubby" Antenna
Gain: 2dBiVSWR: <1.5Power: 100 WInput Impedance: 50 ΩLength: 434MHz 50mm 868MHz 40mm 915MHz 50mmP..
£4.80 Ex Tax: £4.00
Raspberry Pi Camera V2
The Raspberry Pi Camera Module v2 is a high quality 8 megapixel Sony IMX219 imag..
£31.84 Ex Tax: £26.53
LoRaGo OTG Transceiver Dongle
434 & 915MHz units have sold out. We have stock of the 868MHz part, we recommend if you are usin..
£56.39 Ex Tax: £46.99
Flextrak External DS18B20 Temperature Sensor Probe
External DS18B20 temperature probe with adaptor cable for use with our Flextrak boards.Supplied with..
£10.79 Ex Tax: £8.99
Flextrak 2Mtr APRS Addon Board
This is an addon board for Flextrak that gives 2 meter (134-174MHz) APRS functionality to Flextrak. ..
£33.59 Ex Tax: £27.99